# Modeling Friction Performance of Drill String Torsional Oscillation Using Dynamic Friction Model.

1. IntroductionDirectional drilling is a widely used method in the drilling engineering for oil and gas industry. The sliding drilling mode is a critical process that drilling string maintains only axial sliding movement to keep tool face of downhole assembly (BHA) from rotating (the orientation of tool face of BHA can control the direction of wellbore). Excessive axial drag has become a serious problem, especially in extended-reach horizontal wells with a motor/MWD system. Some techniques are available to reduce drill string drag. Rotary steering systems (RSSs) are configured so that the entire drill rotates continuously with steering capabilities. High costs hinder the promotion of RSS technology. Technology called "torque rocking" or pipe torsional oscillation systems [1-4] procedure consists of turning the pipes to the right and then to the left by an amount that avoids interference with the tool face; this is depicted in Figure 1. The phenomenon of friction reduction under the influence of drill string rotation has been understood and utilized by drilling engineer for years. However, the drag reduction mechanism of drill strings' torsional oscillation is not fully understood.

Friction performance is very complex [5]. Pohlman and Lehfeldt [6] found that longitudinal tangential vibrations exert a significantly greater influence on the friction force than the normal ones. Papers argued that [7-10] changes of the friction force vector under the influence of vibrations cyclic are the cause of the reduction of friction resistance. A variable vector of the relative sliding velocity resulted in the force being two components, one of which is parallel and the other of which is perpendicular to the direction of motion. Therefore, only a portion of friction acted in the axial direction of the motion. Consequently, the occurrence friction of transverse tangential vibration was reduced when the driving force was perpendicular to the vibration direction.

Experimental investigations [7-9] attempted to analytically describe this phenomenon. Consistency between analytical and experimental results led to a qualitative fit rather than quantitative agreement [11]. Gutowski and Leus [12] indicated that one of the reasons for the lack of agreement was that these authors utilized only a simple static Coulomb model. The computational model established by other papers [12-14] based on the Dahl model was in good agreement with experimental results. However, the transverse tangential vibration and sliding motion were separated in the plane, and the material properties of the friction pair were the same. The model was not suitable for drill string dynamics analysis because the drill string rotary and sliding on the circular surface and material hardness of the drill pipes and rock wellbore were different. The model [12] also needed a coefficient of vibration transfer to match the experimental results, and the coefficient was difficult to determine for drill engineering. The model neglected the damp of contact zone and the viscosity of motion. It also did not describe the static friction of drill string kinetics; however, it is important for the analysis of drill kinematics [1, 2].

In this work, we presented a dynamic model on the dynamics of the motion of sliding and rotary drill strings for perfectly elastic contact in a viscous fluid environment. Unlike Tsai and Tseng [10], Storck et al. [8], or Gutowski and Leus [12], the discretized LuGre model was utilized for the friction model between the drill string and wellbore rock in a well-hole surface. The computational model establishing process took into account difference in the hardness of the friction pair material in the downhole. This method was more comprehensive for describing the friction between the drill string and wellbore surface.

2. Computational Model

2.1. Surface and Contacts Forms. The axial friction force (or called drag) in axial direction is a focus problem in drilling engineering. Low axial friction can be benefit for drilling. During rotary drilling or "torque rocking," the motion of the drill string is a result of superposition of two motions. The first of these is drill string's tangential rotary motion, whereas the second one is sliding motion in the wellbore's axial direction.

On the macroscopic level, the apparent area of wellbore surfaces observed by the naked eye is "rough" [15]. The drill string surface, apparently a smooth surface, is still "rough" on a microscopic level. The microcontact models [16, 17] assumed that surfaces are composed of hemispherically tipped asperities. The elastic contact of spheres and half spaces are governed Hertz equations to compute the load, contact area, and contact pressure acting on a deformed asperity.

Considering the real contact between the drill string and the borehole rock, we made the same assumption for the contact surface. This implies that the drill string surface is a slightly rough surface and the wellbore is a severe rough surface composed of a large number of elastic bristles, which is an abstraction of asperities. Due to the roughness and hardness difference between the drill string and wellbore rock by surface contact, the general elastic bristle in the dynamic friction model should be the bristles on the wellbore, which, unlike these models, was assumed on the motion body plane contact. The simplified model is shown in Figure 2.

2.2. Basic Assumptions. To analyze the real working conditions of a drill string in a downhole, the following assumptions are made: (1) the bristles on the drill string are rigid, (2) the bristles on the wellbore rock are elastic, and (3) drill string rolling friction will not occur.

2.3. Torque and Drag Computational Model. Based on the above assumptions, the drill string actual working conditions can be simplified into the interaction model as shown in Figure 3. The end point of the general bristle connects with the moving drill string; the connecting point will rupture and rebuild at a different point on the moving body surface with the motion of the drill string. In the LuGre friction model [18], the force was determined from the following equation:

[mathematical expression not reproducible]. (1)

2.3.1. Friction Caused by Bristle Deformation. It assumed in the LuGre model that the rate [??] of the elastic strain of a general bristle in the contact zone depended on both the tangential rigidity [[sigma].sub.1] of the contact zone as well as the relative velocity [v.sub.r] of the sliding and rotary drill string [18, 19]. A generalized form of this expression was represented by the following equation:

[??] = [v.sub.r] - [absolute value of ([v.sub.r])]z/g([v.sub.r]) (2a)

g([v.sub.r]) = ([F.sub.c] + [F.sub.s] - [F.sub.c]) exp (- [([v.sub.r]/[v.sub.s]).sup.2]))/[[sigma].sub.1]. (2b)

In the model for further analysis, the deformation in the contact zone formed by the contact of general bristles sliding and the rotary drill string was modeled by a generalized elastic-damping artificial element ON, which described the average behavior of the general bristles (Figure 4).

An elastic-damping deformation z of the contact artificial element at an optional instant t can be presented in the model as the distance of end points O and N of the element. The scale of artificial elements was the micron level; the curvature of the wellbore surface can be ignored. It was determined by the coordinates of points O and M [10], where M is the projection of point N on the wellbore surface and can be expressed as follows:

[mathematical expression not reproducible]. (3)

The position of M at any instant of wellbore is the result of the superposition of motion caused by the drill string sliding and tangential motion. At consecutive instants, the point M changes its relative position and the elastic deformation z also underwent a magnitude and directional change. The deformation of the elastic bristle was separated into two phases at any interval [DELTA]t [10,12].

In the first phase, during the previous At time step, the instantaneous rotating velocity of the drill string led to the motion of points M in the tangential direction. In the second phase, the motion of point M was the result of the sliding motion of the drill string in the axial direction within At time step.

At a consecutive time interval [DELTA]t, in the first phase of motion, point M moved to the position [M'.sub.1] (t) determined by the following coordinate:

[M'.sub.1] (t) = [[x.sub.1], [y.sub.1]] = [[x.sub.0], [y.sub.0] + [increment of x]]. (4)

At the same time, elastic deformation of the bristle projection vector moved along the path of [mathematical expression not reproducible] to the path [mathematical expression not reproducible]. The general bristle elastic deformation, on the wellbore surface, relied on the contact tangential rigidity [[sigma].sup.1] and damping coefficient of the bristle [[sigma].sup.2]. The deformation changed in its magnitude by an increment of [DELTA]z, which can be evaluated using (4). In Figure 4, z'(t + [DELTA]t/2) was the actual magnitude of elastic deformation of a bristle in the first phase of motion and can be described by the following relationship:

[mathematical expression not reproducible]. (5)

The velocity [v.sub.r1] of the relative motion of the general bristle in the first phase can be determined from the following expression:

[mathematical expression not reproducible]. (6)

Knowing the magnitude of elastic deflection z'(t + [DELTA]t), we can be determine the end point [M'.sub.2] position because the direction of z (t + [DELTA]t) was along vector [mathematical expression not reproducible]. The coordinates were described as follows:

[mathematical expression not reproducible]. (7)

The angle between the elastic deformation [mathematical expression not reproducible] and wellbore axial direction can be determined according to the imposed equation:

[mathematical expression not reproducible] (8)

In the second phase, during the following [DELTA]t time step, drill string sliding led to the motion of points [M'.sub.2] (t+[DELTA]t) in the longitudinal direction. After the expiry of [DELTA]t, the drill string sliding displacement is [increment of x]. This displacement related to the distance of [M'.sub.2][M'.sub.3] (t). The value of [mathematical expression not reproducible] corresponded to the magnitude of elastic deflection of the bristle after the time interval [DELTA]t. This can be described as follows:

[mathematical expression not reproducible]. (9)

Velocity [v.sub.r2] approximately was equal to the average velocity of point [M'.sub.2](t + [DELTA]t) along the straight line O[M'.sub.3](t). The value can be determined from the following equation:

[mathematical expression not reproducible], (10)

where [mathematical expression not reproducible]. The magnitude of [mathematical expression not reproducible] was proportional to [mathematical expression not reproducible], that was M(t+ [DELTA]t), was determined from the following equation:

[mathematical expression not reproducible]. (11)

Angle [beta] between [mathematical expression not reproducible] and the axial direction can be determined by the following expression:

[mathematical expression not reproducible] (12)

Knowing the magnitude and direction of elastic deformation z at any time interval [DELTA]t, the instantaneous values of friction force [f.sub.d] and [m.sub.d] were determined at this instant by utilizing the LuGre model.

[f.sub.d] = [[[sigma].sub.1]z (t + [DELTA]t) + [[sigma].sub.2][??] (t + [DELTA]t)] cos [beta]. (13)

The torque caused by bristle deformation was determined by the following expression:

[m.sub.d] = [R.sub.0][f.sub.y] = [R.sub.0] [[[sigma].sub.x]z (t + [DELTA]t) + [[sigma].sub.2][??] (t + [DELTA]t)] sin [beta]. (14)

2.3.2. Friction Caused by Viscous Fluid. [mathematical expression not reproducible] was the motion viscous force of the drill string in the drilling mud and [mathematical expression not reproducible] was the drill-string motion macroscope velocity vector, not the elastic deformation of the bristle on the wellbore [20]. Hence, the damping coefficient was described in Li (2008), as the following equation:

[mathematical expression not reproducible]. (15)

2.3.3. Average Magnitude of Torque and Drag. The average magnitude force [mathematical expression not reproducible] in the axial direction of the wellbore and during a period of time relates to the magnitude of the friction force in this direction and was essential for initiating and sustaining the drill string motion. It was determined from the following relationship, respectively,

[mathematical expression not reproducible] (16)

The average magnitude torque [mathematical expression not reproducible] during a period of motion of drill string can be described as follows:

[mathematical expression not reproducible]. (17)

Therefore, the average friction drag due to bristle deformation and viscose fluid can be noted, respectively:

[mathematical expression not reproducible]. (18)

[mathematical expression not reproducible] (19)

The average friction torque caused by bristle deformation and viscose fluid can be determined from the following relationship, respectively:

[mathematical expression not reproducible] (20)

[mathematical expression not reproducible]. (21)

3. Model Solution and Model Verification

3.1. Model Calculation Program. Based on the aforementioned calculation model, the solving procedure step of novel dynamic friction model was presented in Figure 5. The procedure included two parts (I and II). Part I presented the bristle elasticity and damping force calculation process on the microlevel including two half-time steps. Part II presented a drilling fluid viscous force at the macrolevel. The macrovelocity vector was the combined longitudinal direction and tangential direction velocity.

3.2. Model Verification. To assess the validity of the established model, experimental data and parameter mentioned in paper [12] were adopted to verify established model. The parameters [12] included a frequency of f = 3000 Hz, a normal pressure of [p.sub.n] = 0.022 N/[mm.sup.2], an area of A = 1200 [mm.sup.2], a coefficient of contact rigidity in tangential direction of [[sigma].sup.1] = 67.29 N/[micro]m, a coefficient of contact damping in tangential direction of [[sigma].sup.2] = 1 x [10.sup.-3] N/([micro]m/s), a coefficient of static friction of = 0.106, and a coefficient of static friction of [[micro].sub.S] = 0.193. There were no fluid effects on the moving body, and the coefficient of viscosity damping was [[sigma].sub.3] = 0N/([micro]m/s).

The experiment presented in the paper was investigated in terms of the influence of tangential contact vibration on the friction force. The aforementioned model was adopted to calculate the change in the friction force with the dimensionless velocity and to compare it with the experimental results (Figure 6). The calculated results are in reasonable agreement with the experimental data. The largest error is 30.17% and the average error is 9.21%.

The model described in the paper by Gutowski and Leus [12] is also in good agreement with the experimental results. However, the influence of a coefficient of vibration transfer in the model [12] is greater than body relative velocity in some conditions. It is also extremely difficult to determine in drill engineering adopting the model described by Gutowski and Leus [12].

4. Discussion and Analysis

4.1. Simulation Parameters. According to the experimental results, the established model can accurately predict the friction from tangential vibration coupled with the sliding motion. Therefore, this model can also describe drill string torsional vibration with sliding in a downhole from a theoretical perspective. Drill pipes in a horizontal wellbore were adopted to analyze axial friction reduction mechanism caused by drill pipe torsional oscillation using general field drilling parameters.

Static and kinetic friction coefficients are fundamental parameters for friction force simulation of drilling string. In the paper [21], static friction coefficient is equal to 0.25 and kinetic friction coefficient is equal to 0.21. Simulation results [21] are in good agreement with the field measured data.

Wang et al. [22] obtained friction stiffness coefficient between steel and rock at different frequencies in the experimental environment. The friction stiffness coefficient is equal to 50 N/mm. This parameter has good consistence with experimental data [22].

However, there are rare reports about friction damping coefficient between steel and rock obtained through experiment research. The parameter can be 0.316 N-s/mm [18], 0.214 N x s/mm [14], and 0.5 N x s/mm [23]. Mehmood et al. (2012) and Yu et al. [24] obtained sensitivity analysis results of parameters in the LuGre friction model. The results showed that coefficient [[sigma].sup.2] is less sensitive as compared to [F.sub.c] and [F.sub.s]. In this paper, damping coefficient [[sigma].sub.2] was equal to 0.316 N x s/mm [18].

Stribeck velocity is also less sensitive than [F.sub.c] and [F.sub.s] according to Mehmood et al. (2012) and Yu et al. [24]. The rock is multiscale porous medium [25]. Giorgio and Scerrato [26] give values of the Stribeck velocity for a multiporous rock medium. Wang et al. [27] provided parameters used in calculating mud damping effects.

Basic simulation parameters were assumed to analyze the drill string axial friction performance affected by rotation and torsional vibration, as shown in Table 1.

4.2. Parameter Sensitivity Study. Tsai and Tseng [10] and Gutowski and Leus [12] described a discrete bristle deformation process based on the Dahl model. This section numerically exploited the influence of two parameters in the LuGre model that the Dahl model does not adopt. Piatkowski [29] analyzed the properties between the Dahl and LuGre dynamic friction models in depth. This section mainly studies the following contents: (1) the importance of taking the Stribeck velocity of the LuGre model into account and (2) the relevance of damping coefficient [[sigma].sub.1] in the longitudinal friction force.

4.2.1. Stribeck Velocity vs Study. Maidla et al. [1, 2] described a force that was applied to a stationary drill string in a downhole and slowly increased until the drill string slides. The sliding resistance experienced two stages, static friction and dynamic friction. The static friction was approximately 25% greater than the dynamic friction. Meanwhile, the LuGre model continues at any instant and can describe dynamic and static characteristics without a velocity piecewise function. This model can also analyze the transition process from static and dynamic friction, which the Dahl model cannot.

The effect of the amplitude of the Stribeck velocity is depicted in Figure 7, which varied from 100 [micro]m/s to 300 [micro]m/s. The axial slide velocity was 277.78 [micro]m/s. The rate of penetration (ROP) was equivalent to 1 m/h. It was a common operation parameter in the horizontal well drilling field.

The simulation result of friction ratio was extremely low using drilling field operation parameters. However, the axial friction ratio held steady with varied Stribeck velocity at the same vibration amplitude. It indicated that the axial friction ratio was low sensitive to the Stribeck velocity using the drilling operation parameter. The result of Yu et al. was also confirmed [24].

4.2.2. Damping Coefficient [[sigma].sub.2] Study. The damping coefficient [[sigma].sub.2] is a microdamping coefficient in the generalized bristle model. Hence, the LuGre model is applied prior to the Dahl model to describe and predict the general bristle deflection process. According to the description of the LuGre model (De Wit and Carlos Canudas, 1995), the damping coefficient of the average behavior of bristle deflection is relative to a parameterization of g([v.sub.r]), which has been proposed to describe the Stribeck effect in (2a) and (2b). This section discusses how varied [[sigma].sub.2] affects the longitudinal friction force.

The numerical results are shown in Figure 8. The longitudinal direction velocity was equal to 1 m/h of ROP. As increasing of vibration amplitude, the axial friction ratio rapidly decreased. However, the greater friction damp coefficient was related to higher axial friction ratio at the same velocity amplitude of torsional vibration. The growth of friction ratio was relatedly low with increasing of damp coefficient. It suggested that damp coefficient of bristle deformation was more sensitive than Stribeck velocity. However, it was little effect of damp coefficient on axial friction as well.

4.3. Viscous Friction of Drilling Mud

4.3.1. Effect of Mud Dynamic Shear. Parametric studies were run to explore the relationship between dynamic shear and axial friction resistance for drill pipes, as shown in Figure 9. ROP was equal to 7m/h. The axial force slowly rises with increasing of the value of dynamic shear. The relationship between the axial force and dynamic shear was approximately linear within the drill string torsional oscillation amplitudes of 10 rpm and 30 rpm. When the dynamic shear is small, it was little distinction of average axial viscous force that affected different torsional vibration amplitude. Value of average axial viscous force increased with dynamics shear. The greater average axial viscous force was with lower torsional vibration amplitude.

4.3.2. Effect of Frequency. This section discussed influence of torsional vibration amplitude of average axial viscous force. The ROP was equal to 7 m/h. The range of torsional oscillation amplitude was between 10 rpm and 30 rpm, while there were common parameters in the drilling fluid. Average axial viscous force decreased with torsional oscillation amplitude increasing (Figure 10). Curve of 1 Hz was slightly higher than curve of 1 Hz. However, curve of 10 Hz was remarkably greater than curve of 1 Hz.

4.3.3. Effect of Viscosity. Axial viscous force was also affected by viscosity of drilling mud. As shown in Figure 11, the viscous force was increasing with the value of viscosity of drilling fluid. However, the whole descending of axial force was remarkable at first and tiny at last with viscosity increasing. In the same as above, the lower torsional vibration amplitude led to greater axial viscous force. It was linear relationship between average axial viscous force and viscosity of fluid. Therefore, it can be effectively reducing axial viscous friction force by enhancing velocity amplitude of torsional vibration.

4.3.4. Axial Viscous Friction Force Reduction. To analyze viscous friction force reduction, axial viscous friction force and viscous friction torque were compared in time domain. As shown in Figure 12, the viscous friction torque was symmetric distribution about zeros. When absolute value of viscous friction torque was increasing, absolute value of axial viscous friction force would be decreasing. When the torque was approaching zero, the axial viscous friction became the greatest. Therefore, axial viscous friction force reduction was due to torsional motion of drill string decomposed of some axial viscous friction force. This axial force reduction mechanism was benefit for drilling engineering.

4.4. Friction of Bristle Deformation

4.4.1. Effect of Torsional Vibration Frequency. The effect of the frequency of torsional oscillation on the axial drag force was discussed in this section. According to the common frequency and amplitude range of torque rocking drilling, 0.1 Hz, 1 Hz, and 10 Hz were selected to analyze the friction reduction in the longitudinal direction. The drill string slide velocity was equal to 0.0025 m/s, corresponding to an ROP of 9 m/h. Other simulation parameters were listed in Table 1.

As shown in Figure 12, the force ratio curves of 0.1 Hz, 1 Hz, and 10 Hz were decreased with torsional vibration amplitude increased. The axial sliding friction force overall decreased, as the frequency of torsional vibration increased from 0.1 Hz to 1 Hz. When the frequency of torsional vibration changed from 1 Hz to 10 Hz, the axial friction overall increased. Thus, these were an optimum frequency that the axial friction was the lowest.

4.4.2. Effect of ROP and Torsional Vibration Amplitude. In addition to studying the interesting drag reduction of torsional oscillation drilling, an analysis was run to explore the relationship between ROP and the longitudinal friction force, as shown in Figure 14. The frequency of torsional vibration was 5 Hz. ROP was between 1 m/h and 9 m/h with 2 m/h step. The amplitude of torsional oscillation was between 10 rpm and 30 rpm with 2 rpm step. Other simulation parameters were listed in Table 1.

The ratio of the axial and Coulomb friction decreased as the torsional oscillation amplitude increased. The reduction rate was remarkable in the region that the amplitude was below 20 rpm, and the downward rate of curves decreased out of that region. The increasing ROP led to a larger axial friction component ratio. The higher axial velocity component of the drill string contributed to a longer length of the bristle projected in the axial direction according the established model (Figure 13).

The curve for the transverse friction force and transverse vibration velocity formed a loop that described hysteresis friction. The relationship between the axial friction force and relatively motion velocity had hysteretic properties, as depicted in Figure 15. There is less difference of loops with 1 m/h, 3 m/h, 5 m/h, 7 m/h, and 9 m/h. The major difference was between 0.1 m/s and 0.15 m/s. This was at the balance position. The deformation directions of bristle were reversed in the y direction. The greater drag velocity led to a larger hysteresis loop. The distinction of loops was tiny to the drilling engineering.

The relationship of axial direction friction and velocity was shown in Figure 16. The curve of each drag velocity also formed a loop. The amplitude of the loop and maximum axial friction resistance increased as the amplitude of torsional oscillation velocity increased. At the maximum velocity, the tangential force rapidly increased and formed peak. Out of range of the maximum velocity, the axial force rapidly decreased and became steady. There were greater peak amplitude and greater steady value with greater drag velocity.

Tiny distinction of tangential force led to larger difference of axial friction in the range of drilling engineering parameters.

4.4.3. Trajectory of the Bristle Deformation Projection. The trajectory of the bristle projection point was depicted in Figure 17. The bristle deformation directly influences the force exerted on the moving drill string. As Figure 17 shows, ROP was between 1 m/h and 9 m/h with 2 m/h step, and the general bristle end point project motion trajectory was influenced by different velocity amplitudes of torsional oscillation.

Shape of trajectory liked a symbol of infinite. However, the trajectory

loops of different drag velocities were symmetric with respect to x = 0. There were intersection of trajectory near the range of x = 0. The number of intersections of trajectory was less with low drag velocity. When drag velocity was above 5 m/h, there were three times of intersection.

The trajectory loop was flat and narrow when the drag velocity was low. However, the loop became wider and curved with increase of drag velocity. The up and down ends of loop were toward the back. It was because stiffness coefficient of bristle deformation was greater than value of Gutowski and Leus [12]. When drag velocity was low, bristle can easily deform in the small area. As drag velocity became great, the bristle cannot deform in the larger range. Therefore, loop with greater ROP was bended to back. Meanwhile the loops became wider.

Projection position of bristle in y direction with time was presented in Figure 18. The trajectories were symmetry with respect to x axial. The curves of different drag velocity were almost superposition. However, the time and position of reversing point with low drag velocity was earlier higher than ones of greater drag velocity. Therefore, the drag velocity mainly influenced peak position of the trajectory in y direction.

The amplitude of trajectory was lower than amplitude of torsional vibration. It was because the connection point between bristle and drilling pipe was ruptured and rebuilt. Meanwhile, there was obvious hysteresis between trajectory of projection point and trajectory of torsional oscillation. In the area that trajectory of torsional vibration intersected with trajectory of projection point, there was obvious difference of trajectory with different drag velocity.

4.5. Relationship of Torque and Drag. Figure 19 presented friction force in axial direction caused by bristle deformation and viscous fluid in time domain. The viscous friction was followed with torsional velocity. The viscous friction decrease with value of torsional velocity became greater. However, friction force due to bristle deformation fell behind by varied torsional velocity. The pattern of two friction forces was mutually consistent. The levels of two friction forces were close to each other.

Figure 20 presented friction torque in axial direction caused by bristle deformation and viscous fluid in time domain. There was also hysteresis between the varied torque caused by bristle deformation and drilling pipe torsional velocity. The value of torque due to bristle deformation increased with the value of friction decrease. There was similar pattern between axial friction force and friction torque caused by bristle deformation. The torque of viscous fluid was obviously lower than ones of bristle deformation.

5. Conclusions

Given the microscope, complex, and field-oriented nature of the current rotation and torsional oscillation drill string axial friction resistance, the goal of this paper was to present a simple dynamic friction model based on the discrete LuGre model for the analysis of tribological effects in horizontal well drilling. This model was established on the basis of the average deflection of the general bristle model and considers the viscosity effect of mud. It is superior for describing the tribological behavior between the drill string and the rock of the wellbore. A computational program was developed to solve the present model, which was utilized to predict instantaneous general bristle deformation and frictional resistance at the contact surface.

The established model was verified using experimental data without adopting a coefficient of vibration transfer. The computational results were consistent with the experimental results. The model can be applied to analyze the frictional resistance of the drill string and wellbore. The parameter sensitivity studies were used to evaluate the effect of the magnitude of the Stribeck velocity and general bristle deformation damp. The results indicated that Stribeck velocity and damp of bristle deformation were not sensitive to friction using the drilling operation parameter.

Drilling parameters of general field were adopted to analyze drill string axial and circumferential friction torque using the present model. The amplitude of dynamic shear and viscosity of drilling mud was positively correlated with the drill string axial friction resistance.

The drag of drilling pipe also decreased with increase of torsional vibration amplitude. There was an optimal frequency that minimizes axial friction in the range of drilling parameters of general field. The axial friction would increase with increase of ROP. There was the order of magnitudes that the value of axial friction caused by bristle deformation and viscous fluid. The torque caused by bristle deformation was greater than ones of viscous fluid in range of drilling parameters of general field.

We introduce this concept into drilling engineering to capture the reality of drill string torque and drag. We can combine the model of conventional drill string mechanics with the discrete LuGre model to forecast proper technology in drilling horizontal wells.

Nomenclature [mathematical Average of friction torque of bristle expression not deformation and viscous fluid, N reproducible] [mathematical Average of friction torque of bristle expression not deformation and viscous fluid, N reproducible] [mathematical A unit vector of axial direction of drill string expression not reproducible] [mathematical Average of friction force of bristle expression not deformation, N reproducible] [mathematical Average of friction force of viscous fluid, N expression not reproducible] [mathematical Average of friction torque of bristle expression not deformation, N reproducible] [mathematical Average of friction torque of viscous fluid, N expression not reproducible] [D.sub.w]: Diameter of wellbore, mm [P.sub.F]: Dynamic friction force, N [F.sub.c]: Coulomb friction force, N [F.sub.fx]: Axial direction component of dynamic friction force, N [F.sub.fy]: Tangential direction component of dynamic friction force, N [F.sub.s]: Static friction force, N [R.sub.0]: Outer diameter of drill string, mm [f.sub.d]: Friction force of bristle deformation, N [f.sub.v]: Friction force of viscous fluid, N [m.sub.d]: Friction torque of bristle deformation, N [m.sub.v]: Friction torque of viscous fluid, N [v.sub.r]: Velocity of relative motion drill string, m/s [v.sub.r1]: Virtual relative velocity of motion drill string in previous half of time step, [micro]m/s [v.sub.r2]: Virtual relative velocity of motion drill string in following half of time step, [micro]m/s [v.sub.s]: Stribeck velocity, [micro]m/s [v.sub.x]: Axial direction velocity component of motion drill string, m/s [v.sub.y]: Instantaneous tangential direction velocity component of motion drill string, m/s [x.sub.1]: x coordinate of end point of bristle projection [M'.sub.1], [micro]m [x.sub.2]: x coordinate of end point of bristle projection [M'.sub.2], [micro]m [x.sub.3]: x coordinate of end point of bristle projection [M'.sub.2], [micro]m [y.sub.1]: y coordinate of end point of bristle projection [M'.sub.1], [micro]m [y.sub.2]: y coordinate of end point of bristle projection [M'.sub.2], [micro]m [y.sub.3]: y coordinate of end point of bristle projection [M'.sub.2], [micro]m [[sigma].sub.1]: Tangential stiffness of general bristles, N/[micro]m [[sigma].sub.2]: Damp coefficient of general bristles, N/([micro]m/s) [[sigma].sub.3]: Damp coefficient of mud viscous friction, N/(m/s) [D.sub.w]: The well-hole inner diameter, m dx: The length of drilling pipes, m [R.sub.0]: The outer radius of drilling pipes, m v: The axial velocity of drilling pipes considering fluid, consist of [v.sub.x] and mean velocity of fluid, m/s [alpha]: Angle between virtual elastic deformation vector of general bristle and axial direction, rad [beta]: Angle between elastic deformation vector of general bristle and axial direction, rad [lambda]: Coefficient of drill string eccentric, dimensionless [mu]: Viscosity of drilling mud, Pa x s [tau]: Dynamic shear of drill string, MPa [omega]: The rotating angular velocity of drilling pipe, rad/s M: End point of bristle projection n: Number of time step in one second, dimensionless x: x coordinate of end point of bristle projection M, [micro]m y: y coordinate of end point of bristle projection M, [micro]m z: Elastic deformation of general bristles, [micro]m z': Virtual elastic deformation of general bristles in the calculation time step, [micro]m [DELTA]t: Time step, le - 6 s [increment of x]: Axial direction relative displacement of motion drill string in one time step, [micro]m [increment of y]: Axial direction relative displacement of motion drill string in one time step, [micro]m [OMEGA]: Amplitude of torsional oscillation, rpm [V.sub.r]: Macroscope velocity relative to drilling fluid, m/s.

Additional Points

Highlights. An improved discrete LuGre model and method for describing and predicting the friction between a drill string and wellbore rock was established for given downhole conditions. The influence of mud properties and torsional oscillation parameters on the axial and transverse friction resistance was discussed based on the established model.

https://doi.org/10.1155/2017/4051541

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This research was sponsored by the National Natural Science Foundation of China (Grant no. 51274171), the Sichuan Province Science & Technology Program (Grant no. 2015SZ0003), and the National Science and Technology Major Project of China (Grant no. 2016ZX05022-01).

References

[1] E. Maidla and M. Haci, "Understanding Torque: The Key to Slide-Drilling Directional Wells," in Proceedings of the IADC/SPE Drilling Conference, Society of Petroleum Engineers, Dallas, Tex, USA, 2004.

[2] E. Maidla, M. Haci, S. Jones, M. Cluchey, M. Alexander, and T. Warren, "Field proof of the new sliding technology for directional drilling," in Proceedings of the 2005 SPE/IADC Drilling Conference - Drilling Technology: Back to Basics, pp. 723-730, February 2005.

[3] E. Maidla, M. Haci, and D. Wright, "Case history summary: Horizontal drilling performance improvement due to torque rocking on 800 horizontal land wells drilled for unconventional gas resources," in Proceedings of the SPE Annual Technical Conference and Exhibition 2009, ATCE 2009, pp. 195-206, October 2009.

[4] C. Gillan, S. Boone, G. Kostiuk, C. Schlembach, J. Pinto, and M. LeBlanc, "Applying precision drill pipe rotation and oscillation to slide drilling problems," in Proceedings of the SPE/IADC Drilling Conference and Exhibition 2009, pp. 53-65, March 2009.

[5] M. Urbakh, J. Klafter, D. Gourdon, and J. Israelachvill, "The nonlinear nature of friction," Nature, vol. 430, no. 6999, pp. 525-528, 2004.

[6] R. Pohlman and E. Lehfeldt, "Influence of ultrasonic vibration on metallic friction," Ultrasonics, vol. 4, no. 4, pp. 178-185, 1966.

[7] S. Matunaga and J. OnodA, "A novel method of friction force reduction by vibration and its application to gravity compensation," in Proceedings of the 33rd Structures, Structural Dynamics and Materials Conference, Dallas, Tex, USA, 1992.

[8] H. Storck, W. Littmann, J. Wallaschek, and M. Mracek, "The effect of friction reduction in presence of ultrasonic vibrations and its relevance to travelling wave ultrasonic motors," Ultrasonics, vol. 40, no. 1-8, pp. 379-383, 2002.

[9] V. C. Kumar and I. M. Hutchings, "Reduction of the sliding friction of metals by the application of longitudinal or transverse ultrasonic vibration," Tribology International, vol. 37, no. 10, pp. 833-840, 2004.

[10] C. C. Tsai and C. H. Tseng, "The effect of friction reduction in the presence of in-plane vibrations," Archive of Applied Mechanics, vol. 75, no. 2-3, pp. 164-176, 2006.

[11] P. Gutowski and M. Leus, "The effect of longitudinal tangential vibrations on friction and driving forces in sliding motion," Tribology International, vol. 55, pp. 108-118, 2012.

[12] P. Gutowski and M. Leus, "Computational model for friction force estimation in sliding motion at transverse tangential vibrations of elastic contact support," Tribology International, vol. 90, pp. 455-462, 2015.

[13] X. Wang, P. Chen, and T. Ma, "a. Modeling and experimental investigations on the drag reduction performance of an axial oscillation tool," Journal of Natural Gas Science Engineering, pp. 39-118, 2017.

[14] A. Mehmood, S. Laghrouche, M. El Bagdouri, and F. S. Ahmed, "Sensitivity analysis of lugre friction model for pneumatic actuator control," in Proceedings of the 2010 IEEE Vehicle Power and Propulsion Conference, VPPC 2010, September 2010.

[15] P. S. M. Dougherty, R. Pudjoprawoto, and C. Fred Higgs, "Bit cutter-on-rock tribometry: Analyzing friction and rate-of-penetration for deep well drilling substrates," Tribology International, vol. 77, pp. 178-185, 2014.

[16] J. A. Greenwood and J. B. P. Williamson, "Contact of nominally flat surfaces," Proceedings of the Royal Society of London A: Mathematical, Physical and Engineering Sciences, vol. 295, no. 1442, pp. 300-319, 1966.

[17] A. Majumdar and B. Bhushan, "Fractal model of elastic-plastic contact between rough surfaces," Journal of Tribology, vol. 113, no. 1, pp. 1-11, 1991.

[18] C. Canudas de Wit, H. Olsson, K. J. Astrom, and P. Lischinsky, "A new model for control of systems with friction," IEEE Transactions on Automatic Control, vol. 40, no. 3, pp. 419-425, 1995.

[19] H. Olsson, K. J. Astrom, C. Canudas De Wit, M. Gofvert, and P. Lischinsky, "Friction Models and Friction Compensation," European Journal of Control, vol. 4, no. 3, pp. 176-195, 1998.

[20] S. A. Mirhaj, "Evaluation of Shear Forces and Stream-Thrust Forces in Torque and Drag Analysis," in Proceedings of the SPE Asia Pacific Oil and Gas Conference and Exhibition, Jakarta, Indonesia, 2001.

[21] E. Cayeux, H. J. Skadsem, B. Daireaux, and R. Holand, "Challenges and Solutions to the Correct Interpretation of Drilling Friction Tests," in Proceedings of the SPE/IADC Drilling Conference and Exhibition, The Hague, The Netherlands, 2017.

[22] P. Wang, H. Ni, R. Wang, Z. Li, and Y. Wang, "Experimental investigation of the effect of in-plane vibrations on friction for different materials," Tribology International, vol. 99, pp. 237-247, 2016.

[23] M. R. Kermani, R. V Patel, and M. Moallem, "Friction identification in robotic manipulators: case studies," in Proceedings of 2005 IEEE Conference on Control Applications, 2005. CCA 2005, pp. 1170-1175, Toronto, Canada, 2005.

[24] Y. Yu, Y. Li, and J. Li, "Parameter identification and sensitivity analysis of an improved LuGre friction model for magnetorheological elastomer base isolator," Meccanica, vol. 50, no. 11, pp. 2691-2707, 2015.

[25] H. Dou and Y. Yang, "Further understanding on fluid flow through multi-porous media in low-permeability reservoirs," Petroleum Exploration and Development, vol. 39, no. 5, pp. 674682, 2012.

[26] I. Giorgio and D. Scerrato, "Multi-scale concrete model with rate-dependent internal friction," European Journal of Environmental and Civil Engineering, pp. 1-19, 2016.

[27] X. Wang, H. Ni, and R. Wang, "b. Modeling and analyzing the movement of drill string while being rocked on the ground," Journal of Natural Gas Science Engineering, pp. 39-28, 2017.

[28] Z. F. Li, "Fundamental equations and its applications for dynamical analysis of rod and pipe string in oil and gas wells," Acta Petrolei Sinica, vol. 20, no. 3, pp. 87-90,1999.

[29] T. Piatkowski, "Dahl and LuGre dynamic friction models The analysis of selected properties," Mechanism and Machine Theory, vol. 73, pp. 91-100, 2014.

Xingming Wang, (1) Ping Chen, (1) Zhenhua Rui, (2) and Fanyao Jin (3)

(1) State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu, China

(2) Independent Project Analysis Inc., Washington, DC, USA

(3) School of Mechatronic Engineering, Southwest Petroleum University, Chengdu, China

Correspondence should be addressed to Xingming Wang; upjzk@sina.com

Received 2 January 2017; Revised 10 June 2017; Accepted 2 July 2017; Published 14 August 2017

Academic Editor: Giorgio Dalpiaz

Caption: FIGURE 1: Schematic diagram of "torque rocking".

Caption: FIGURE 2: Modeling of contact's elastic deformation.

Caption: FIGURE 3: Distribution of forces acting on the sliding and torsional oscillation of the drill string.

Caption: FIGURE 4: Changes in a general bristles deformation at consecutive phases of sliding and torsional oscillation of the drill string.

Caption: FIGURE 5: Present model solution flow chart.

Caption: FIGURE 6: Comparison between the numerical simulation and experimental results.

Caption: FIGURE 7: Influence of the Stribeck velocity on the change in friction.

Caption: FIGURE 8: Influence of the damp coefficient of general bristles on the change in friction.

Caption: FIGURE 9: Influence of dynamic shear of drilling mud on the change in axial viscous force.

Caption: FIGURE 10: Influence of frequency of torsional oscillation on the axial viscous force.

Caption: FIGURE 11: Influence of viscosity of drilling mud on the change in axial viscous force.

Caption: FIGURE 12: Viscous force and torque of drillingpipes in time domain.

Caption: FIGURE 13: Influence of frequency of torsional oscillation on the axial friction due to bristle deformation.

Caption: FIGURE 14: Influence of amplitude of drill string torsional oscillation on the change in axial friction.

Caption: FIGURE 15: Influence of different amplitudes of torsional oscillation on transverse friction.

Caption: FIGURE 16: Loop of the axial force of the drill string and relative motion velocity.

Caption: FIGURE 17: Trajectory of general bristle end point projection.

Caption: FIGURE 18: Trajectory of bristle projection and drilling pipe torsional oscillation in time domain.

Caption: FIGURE 19: Friction force of bristle deformation and viscous fluid in time domain.

Caption: FIGURE 20: Friction torque of bristle deformation and viscous fluid in time domain.

TABLE 1: Simulation parameters [12, 26-28]. Number Parameter/unit Value 1 Coulomb friction coefficient 0.21 2 Static friction coefficient 0.25 3 Friction Stiffness coefficient/(N/mm) 50 4 Friction Damping coefficient/(N/(mm/s)) 0.316 5 Stribeck velocity/([micro]m/s) 190 6 Length of drill pipe/m 10 7 Outer diameter of drill pipe/m 0.127 8 Inner diameter of drill pipe/m 0.1086 9 Wellbore diameter/m 0.2156 10 Dynamic shear/Pa 15 11 Viscosity/Pa x s 0.03 12 Density of drill pipe/(kg/[m.sup.3]) 7850 13 Density of drill mud/(kg/[m.sup.3]) 2200 14 Volume rate/(L/s) 30

Printer friendly Cite/link Email Feedback | |

Title Annotation: | Research Article |
---|---|

Author: | Wang, Xingming; Chen, Ping; Rui, Zhenhua; Jin, Fanyao |

Publication: | Shock and Vibration |

Article Type: | Report |

Date: | Jan 1, 2017 |

Words: | 7271 |

Previous Article: | Study on Vibration Reduction Method for a Subway Station in Soft Ground. |

Next Article: | Nonlinear Dynamics Mechanism of Rock Burst Induced by the Instability of the Layer-Crack Plate Structure in the Coal Wall in Deep Coal Mining. |

Topics: |